List of brushless whoop/toothpick flight controllers

This is the list of brushless tiny whoop/toothpick style flight controllers with brief description and features list. You can compare them and choose the best whoop/toothpick type FC that suits your needs. The list contains only the AIO boards – flight controllers with 4in1 ESC.

A note on the prices – IC prices were skyrocketing in the year 2020-2021 and so were the prices for flight controllers. Most likely the prices posted here will be incorrect by the time you will be reading this article.

Page Contents for List of brushless whoop/toothpick flight controllers

Types of the flight controllers

Whoop flight controller has a shape of the rotated square board with a 25.5×25.5mm mounting holes pattern. USB socket and motor sockets are usually located on the bottom side of the FC and are faced downwards. Typical whoop frames are designed to have this layout in mind so should fit into most of the whoop frames.

LDARC brushless whoop FC

Toothpick flight controller has the same whoop form factor and should fit on the same mount holes. However it usually has bigger size, and might not fit into whoop frames. Toothpick flight controller often has separate solder pads for motor wires. USB socket is located horizontally flat. Toothpick type flight controllers usually have higher current output for motors, some flight controllers reaching even up to 45A.

BetaFPV brushless toothpick FC

You can see that different manufacturers are declaring different distance between the mounting holes. Typically it should be in the range 25.526.0 mm. This is due to misinterpretation and lack of unified standard. Originally this distance should be counted as 1 inch (2.54cm)

FC main parameters

MCU – modern whoop/toothpick flight controllers have F4 (F405, F411) or even F7 type STM32 microcontroller (MCU). Betaflight stopped supporting F1 and F3 MCU’s already, so they are not recommended for the new builds. F411 MCU has only 2 full hardware UARTS. Read more about Flight controllers MCU types here. There is new G4 MCU coming into the market, replacing the old F4 MCU.

OSD – having OSD in your FPV feed is really handy. You can see the current flight mode, battery voltage, current, battery consumption, warnings and even more valuable information.

Current Sensor – if the flight controller has current sensor, then you will be able to add the current amperage value indicator as OSD element in the FPV feed. Also you can have battery consumption indicator.

ESC amps – the max ESC amps shows how much power can whoop FC deliver to the motors. The bigger and the faster motors – the more amps you need to deliver.

Battery input voltage – shows what cell count batteries can be used with this flight controller. Modern flight controllers support 2-4S or even 2-6S.

Integrated receiver – integrated receiver eliminates the need of soldering the external receiver, greatly reduces the weight and complexity of the build. Usually built-in receivers are connected via so called SPI line, so directly controlled by the MCU. The biggest concern using the built-in receiver is the relatively short control range with some rare exceptions like ExpressLRS SPI receivers.

Whoop Toothpick Flight Controllers

Here is the spreadsheet with all the listed flight controllers: http://bit.ly/Whoop-Toothpick-Flight-Controller-list-spreadsheet

Crazybee F4 2-4S Brushless Flight Controller V3

Price ~ $47.99

https://www.banggood.com/Eachine-Crazybee-F4-PRO-V3_0-Flight-Controller-Blheli_S-10A-2-4S-Brushless-ESC-compatible-Frsky-Flysky-Receiver-for-Cinecan-4K-Racing-Drone-p-1534753.html

http://www.happymodel.cn/index.php/2019/07/26/crazybee-f4-pro-v3-0-2-4s-compatible-flight-controller/

The third (actually – fourth) version of the popular Crazybee F4 Pro flight controller. This time Happymodel upgraded the ESC chips and now it provides 10A (12A burst) current to motors and supports 2-4S battery input. FC has OSD, current meter and comes with FrSky, Flysky or no RX options.

Release date: 2019-07

Specifications of FC:

  • MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
  • Sensor: MPU-6000 (SPI connection)
  • Board size: 28.5 * 28.5MM
  • Power supply: 2-4S battery input (DC 7-17V)
  • Built-in 10A (each) Blheli_S 4in1 ESC Dshot600 ready
  • Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable)
  • Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS2A switchable)
  • No RX version need to add external Receiver
  • Built-in Betaflight OSD (SPI Control)
  • Built-in Current meter Max 70A (scale set to 470)
  • Built-in 5V 1A BEC
  • Built-in voltage detection
  • Weight: ?

Specifications of ESC:

  • MCU upgraded to EFM8BB21
  • Power supply: 2-4S LiPo/LiPo HV (7v/17v)
  • Current: 10A continuous peak 12A (5 seconds)
  • Support BLHeliSuite programmable
  • Factory firmware: F_H_40_REV16_5.HEX
  • Default protocol: DSHOT600

Crazybee F4 Lite 1S Brushless Flight Controller

Price ~ $47.99

https://www.banggood.com/Happymodel-Mobula6-Part-Crazybee-F4-Lite-1S-Flight-Controller-AIO-ESC-Receiver-25mW-VTX-for-RC-Drone-p-1625619.html

Crazybee F4 Lite is the lightest flight controller from Happymodel. It is designed to work only with 1S batteries. On board ESC provides up to 5A (6A burst) curent to motors. Board has OSD, but no current meter, just battery voltage sensing. The most interesting feature is on-board VTX with the power output of 25mW.

Release date: 2019-11

Specifications of FC:

  • MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
  • Sensor: MPU-6000 (SPI connection)
  • Board size: 28.5 * 28.5MM
  • Power supply: 1S battery input (DC 2.9V-4.35V)
  • Built-in 5A (each) Blheli_S 4in1 ESC Dshot600 ready
  • Built-in Betaflight OSD(SPI Control)
  • Built-in 5.8G VTX
  • Built-in SPI Frsky/Flysky receiver
  • Built-in 5V 1A BEC
  • Built-in voltage detection

CrazyF411 AIO flight controller

Price ~$48.99

Makerfirehttps://shop.makerfire.com/collections/new-arrival/products/happymodel-crazzyf411-aio-f4-flight-controller

Happymodel CrazyF411 supports 2-4s battery input and provides 20A to the motors.  One of the most interesting features is the integrated SPI Frsky receiver working with D8/D16 protocols. This integrated receiver has PA/LNA power amplifier and the diversity antenna. This should give more control range for this flight controller.

Release date: 2020-10

Specifications:

F4 Flight Controller MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000 (SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 2-4S battery input (DC 8V-17V)
Built-in 20A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Frsky D8/D16 SPI receiver

Built-in 2.4G Power Amplification
Built-in Betaflight OSD(SPI Control)
Built-in Current meter
Built-in 5V 1.5A BEC
Built-in voltage detection
Firmware target: MATEKF411RX
Yaw Degrees should set to “-90 degree” to match the flight direction
Onboard 20A ESC MCU upgraded to EFM8BB21
Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Current: 20A continuous peak 25A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: F_H_40_REV16_7.HEX
Default protocol: DSHOT600
Internal Frsky NON-EU receiver Version
SPI BUS receiver
Frsky D8/D16 compatible

Compatible Non EU transmitter both D8 mode and D16 mode
Channels: 8ch/16chDual antenna
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 400m

Features:
– 25.5×25.5mm FC AIO ESC board for toothpick .
– Most powerful for whoop / toothpick style flight
– Supports 2-4s battery input and provides 20A to the motors.
– Also Integrated SPI Frsky receiver working with D8/D16 protocols.
This integrated receiver has PA/LNA power amplifier and the diversity antenna.
This should give more control range for this flight controller.

Diamond F4 5in1 AIO flight controller

Price ~ $48.99

Makerfirehttps://shop.makerfire.com/products/happymodel-diamondf4-flight-controller

Happymodel DiamondF4 AIO FC is the lightest whoop flight controller with integrated Frsky or Flysky receiver and integrated VTX. Integrated VTX can be switched from 25mw to 200mw of power output. Other features are pretty standard – F411 MCU, MPU-6000 SPI gyro, 5A (6A burst) 4in1 ESC, OSD and Current sensor, but the total weight of the 5in1 AIO FC is only 3.42 grams!

Release date: 2021-01

Specifications:
(Frsky SPI RX version) DiamondF4 FR FC Firmware target: CrazybeeF4FR
(Flysky SPI RX version) DiamondF4 FS FC Firmware target: CrazybeeF4FS
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000 (SPI connection)
Original whoop size compatible
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD (SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky/Flysky receiver
Built-in 5V 1A BEC

Onboard 4in1 ESC
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HV Current: 5A continuous, peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT600

Onboard Frsky SPI D8 receiver Version
SPI BUS receiver Frsky D8 compatible
Compatible Non EU transmitter D8 model Channels: 8ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m

Onboard Flysky SPI receiver Version
SPI BUS receiver protocols: AFHDS and AFHDS-2A Switchable
Channels: 8ch (AFHDS) or 14ch (AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m
Failsafe support

Onboard 5.8g VTX
Output power: 25mw~200mw switchable
Frequency: 40CH
Input voltage: 3.3V – 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels(include Race band) Smartaudio ready

Happymodel ELRS F4 2G4 AIO 5in1 Flight controller

Price ~$65.99

https://www.banggood.com/Happymodel-ExpressLRS-ELRS-F4-2G4-AIO-5IN1-Flight-Controller-…-1850633.html

Happymodel ELRS F4 2G4 AIO is the first flight controller with ExpressLRS 2.4GHz SPI receiver on board and the first board with on board SMD ceramic antenna. ExpressLRS allows to have ultra fast 500Hz rate link and great range even with on board antenna. This AIO FC also has 25-200mW VTX on board, 5A (6A) 1S 4in1 ESC, current and voltage sensors.

Release date: 2021-05

Specifications
Flight controller
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Whoop size compatible
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD (SPI Control)
Built-in 5.8G VTX
Built-in SPI ExpressLRS 2.4GHz receiver
Built-in 5V 1A BEC
Flight controller firmware target: CRAZYBEEF4SX1280

Onboard 4in1 ESC
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT600
Onboard SPI
ExpressLRS 2.4GHz Receiver Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHzAntenna: SMD antenna
Telemetry output Power: <12dBm

Receiver protocol: SPI ExpressLRS Could bind with Happymodel ES24TX , ES24TX Lite, ES24TX Slim and DIY 2.4GHz ELRS TX module(need to flash the same version ELRS firmware)

Onboard 5.8g VTX
Output power: 25mw~200mw switchable
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA
Frequency: 5.8GHz 5bands 40 channels(include Race band)
Smartaudio ready
Onboard voltage and Amperage meters settings Voltage meter scale setting 110

Aikon F7 60A AIO

Price ~$??.??

https://www.aikon-electronics.com/index.php?id=40

The first AIO with  60A (70A burst) of output current output capable ESC on the market. Aikon F7 AIO board features 5 full UARTS, on board 16MB black box. The gyro sensor is the trending Bosh BMI270, as the era of the MPU-6000 is ending. The board also has software controlled VTX power switch (assigned to USER1 mode by default).

Release date: 2022-05

Specifications:
Flight Control Firmware: Betaflight
Target: AIKONF7
MCU: STM32F722
IMU: BMI270 (interrupt pin connected)
Blackbox: SPI 16MB
ESC Firmware: BLHeli_S (Supports BlueJay)
Ports: 5 UARTS
Constant Current: 60A
Burst Current: 70A
Current Sensor Scale: 400
Battery: 3-6s
Mount Holes: 25.5*25.5mm
Weight: 14g

BetaFPV F4 35A 2-6S Brushless Flight Controller

Price ~$74.99

https://betafpv.com/products/toothpick-f4-2-6s-aio-brushless-flight-controller-35ablheli_32

This FC is the first BLHeli_32 35A all-in-one toothpick FC on the market. The ESC runs on BLHeli_32, is capable of 35A (40A burst) and supports 2-6S Lipo battery. 3 UARTS are available (one of them is SoftSerial though) and it fully supports DJI digital FPV.

Release date: 2020-02

Specifications of FC:

  • Item: F4 35A AIO FC(BLHeli_32)
  • Weight: 7g
  • CPU: STM32F411CEU6
  • Six-Axis: MPU6000 (SPI connection)
  • Mounting hole size: 26mm * 26mm
  • Firmware version: BETAFPVF411 (BEFH)
  • OSD: Built-in BetaFlight OSD (OSD chip: AT7456E)
  • Support programmable LED like WS2812 etc
  • Built-in current sensor

Specification of ESC

  • Signal support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
  • Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/Flysky Receiver/DSMX Receiver/TBS Crossfire Receiver (requires external connection)
  • Input voltage: 2S-6S Lipo
  • Continuous current: 35A
  • Peak current: 40A
  • ESC firmware: BLHELI_32
  • Indicators: 3 indicators: receiver indicator (green)/Flight control status indicator (blue)/Flight control power indicator (red)
  • Capacitor: CS|5*10*17mm|680μF|35V
  • Connecter: XT60U 14AWG
  • Recommended motors: 140X series, 150X series, 160X series, 180X series

BetaFPV F4 20A 2-4S Brushless Flight Controller

Price ~$59.99

https://betafpv.com/products/f4-20a-aio-1-4s-brushless-flight-controllerblheli_s

The most powerful whoop flight controller. It runs on F4 MCU and its ESCs are capable of 20A (25A burst).

Release date: 2019-10

Specifications of FC:

  • CPU: STM32F411CEU6 (100MHZ)
  • Six-Axis: MPU6000 (SPI connection)
  • Size: 32.5*32.5mm (26.5mm mounting holes)
  • Firmware version: Betaflight MATEKF411 (MK41)
  • OSD: Built-in BetaFlight OSD (OSD chip: AT7456E)
  • Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/ Flysky Receiver/ TBS Crossfire Receiver/DSMX Receiver
  • Support programmable LED like WS2812 etc
  • Built-in current sensor
  • Weight: 5.63g

Specifications of ESC:

  • Support BLheli/BLHELI_S suite Pass-through ready
  • Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
  • Input voltage: 2S-4S Lipo
  • Continuous current: 20A
  • Peak current: 25A
  • Firmware: BLHELI_S
  • Motor Connectors: 1.25mm header pins connector

BetaFPV F4 1S Brushless Flight Controller V2.1 V2.2

Price ~$39.99

https://betafpv.com/products/f4-1s-brushless-flight-controller-v2-0-frsky-rx

The lightest F4 1S brushless FC in the market. Total weight in only 2.69 grams. Brushless 4in1 ESCs are capable up to 5A (6A peak). It comes in versions with Frsky, Futaba, DSM onboard SPI receiver or without receiver. Notice, that it has EFM8BB10 ESC MCU and that means it is not compatible with JESC firmware (but you can flash JazzMac ESC BLHeli_s firmware).

If you are into building the super-light brushless whoop, then this board is definitely for you.

Version 2.2 has updated BEC and now includes power cable with BT2.0 connector.

V2.1

V2.2

Release date: 2019-09

Specifications of FC:

  • CPU: STM32F411CEU6 ( 100MHZ )
  • Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
  • Size: 29mm x 29mm, fully compatible with the whoop frame in the current market, Beta65 Pro frameBeta75 Pro frame, BWhoop B06 frame, and mounting pattern
  • Firmware version: Betaflight MATEKF411RX (MK41R)
  • Compatible with Z02A01M01 VTX
  • OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
  • Power Cable V2.1: 60mm, with JST-PH 2.0 connector, 1.25mm motor header pins; V2.2: Power Cable: 55mm, with BT2.0 connector
  • Weight: 2.69g 

Specifications of ESC:

  • Power supply: 1S
  • Current: 5A continuous and peak 6A (3 seconds)
  • Support BLHeliSuite programmable
  • Factory firmware: O_L_5_REV16_6.HEX
  • Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM

BetaFPV F4 1S AIO VTX Brushless Flight Controller

Price ~ $39.99

https://betafpv.com/search?type=product%2Carticle%2Cpage&q=F4+1S+AIO

The first BetaFPV flight controller with integrated Receiver and VTX. This board has 25mW video transmitter and will be available in NoRX, FrSky FCC/LBT, DSMX and Futaba on board receiver options.

Release date: 2020-09

Specifications of FC:

  • CPU: STM32F411CEU6 ( 100MHZ )
  • Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
  • Size: 29mm x 29mm, fully compatible with the whoop frame in the current market, Beta65 Pro frameBeta75 Pro frame, BWhoop B06 frame, and mounting pattern
  • Firmware version: Betaflight MATEKF411RX (MK41R)
  • 3pin connector for camera input
  • OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
  • Power Cable: 60mm, with JST-PH 2.0 connector, 1.25mm motor header pins
  • Weight: ?.??g 

Specifications of ESC:

  • Power supply: 1S
  • Current: ?A continuous and peak ?A (3 seconds)
  • Support BLHeliSuite programmable
  • Factory firmware: ?.HEX
  • Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM

Diatone MAMBA F411 25A AIO MK2

Price $53.99 $68.99

https://www.banggood.com/Mamba-AIO-F411-MK2-F4-Flight-Controller-OSD-5V-BEC-25A-2-4S-Blheli_S-Brushless-ESC-Stack-External-USB-for-RC-Drone-FPV-Racing-p-1840653.html

This is second generation MAMBA F411 AIO board from Diatone. This board is pretty much the same as previous gen F411 25A AIO whoop board, just with the external USB connector. USB connector (USB-C or Micro USB) is populated on the small external breakout board and the board is connected with the 4 silicone wires. This allows you to mount the USB connector anywhere on your frame.

Release date: 2021-03?

Diatone Mamba F411 25A AIO MK2 Connection diagram:

Diatone MAMBA F722 35A AIO MK1

Price $63.99 $99.99

https://www.banggood.com/MAMBA-AIO-F722-MK1-F7-Flight-Controller-35A-2-6S-Blheli_S-Brushless-ESC-External-…-1840673.html

This is first generation MAMBA F722 AIO board from Diatone. This board comes with two options – internal or external USB connector. External USB connector (USB-C or Micro USB) is populated on the small external breakout board and the board is connected with the 4 silicone wires. This allows you to mount the USB connector anywhere on your frame. Everything else is pretty much the same as  F411 25A AIO.

Release date: 2021-?

Diatone Mamba F722 35A AIO MK1 Connection diagram:

Specifications:
MCU: 216MHz STM32F722RET6
GYRO: MPU6000
Barometer: Yes
OSD: Yes
Blackbox: NO
Uarts: 5
ESC Soft: Dshot300/600
Power Led: Yes
LED Controller: BF LED
F.Port: Yes
RSSI: No
Buzz: Yes
Input: 2~6S Lipo (8.4~25.2V)
TVS Protection: Yes
BEC: 5V 2.5A
Mounting: 25.5mm ,M2

ESC Specifications
Input voltage: 2~6S Lipo (8.4V~25V)
Continuous current: 35A×4
Burst current: 45A (10S)
Target:BLHeli_S GH30
SOFT: Dshot300/600

Eachine Cvatar F722 AIO Flight Controller 25A

This flight controller is actually the “inspired” from or just a rebrand of the HGLRC Zeus25 AIO board with slightly different mounting holes and different PCB color. Eachine Cvatar F722 AIO is capable of 25A (30A burst) output, accepts 3-6S battery.  ESCs have BLHELI_32 firmware, but there is no current sensor installed on board.

Price ~ $68.99

https://www.banggood.com/25_5X25_5mm-Eachine-Cvatar-AIO-F722-F7-3-6S-Flight-Controller-25A-…-1835305.html

Specifications:
Name: Eachine Cvatar F722 AIO Flight Controller 25A Blheli_32 4 IN 1 Brushless ESC
FC Firmware: BF EACHINEF722 AIO
F722 FC+25A BL32 ESC
Input Voltage: 3-6S
FC Firmware: BF EACHINEF722 AIO
ESC Firmware: BLHeli_32
F722 Flight Controller
CPU: STM32F722
MPU: MPU6000
OSD: Support
BEC: 10V/1A
BEC: 5V/2A
LED: Support
BlackBox: NO
UART: 5
Current Sensor: not support
Constant Current: 25A
Peak Current: 30A(10s)
Installing Hole: 25.5X25.5mm.M2
Dimensioms: 32.5×32.5mm
Weight: 8.1g

Foxeer Reaper F745 45A BLS 2-6S AIO

Price ~ $99.99

Foxeerhttps://www.foxeer.com/foxeer-reaper-f745-45a-bls-2-6s-aio-g-376

Reaper F745 is the first AIO FC from Foxeer and it’s the third AIO FC with F745 MCU on the market. Supports 2-6S battery input and outputs up to 45A (50A burst) of current to motors. Plenty of UARTS (has 5) and has 8Mb black box on board. Powerful AIO board with standard features. Nothing fancy.

Release date: 2020-11

Foxeer Reaper F745 45A 2-6S AIO connection/pinout diagram:

Specifications:
Model: FOXEER Reaper AIO
CPU: STM32F745
Power Supply: 2~6S Lipo (8.4~25.2V)
BEC Output: DC5V/2.5A
OSD: BF OSD
Black Box: 16M Flash Memory
UART: 5 Set
USB: Micro USB
Fireware: FOXEERF745_AIO
DJI Connector: Supported, 8pin
Size: 32.5X32.5mm
Mounting Hole: 25.5X25.5mm,Φ3mm/M2
Weight: 8.6g
Working Temperature: -20℃ ~ +55℃
Working Humidity: 20~95%
Storage Temperature: -20℃ ~ +70℃
Package Includes: 1*AIO, Rubbers Columns, XT30 Cable, DJI Cable, Capacity

ESC Firmware: G-H-30 BLS 16.7
Continuous /Burst Current: 45A x 4/ 50A x 4
Input Voltage: 2~6S Lipo (8.4~25.2V)
Telemetry: No
ESC Programming: BLHeli-S
Stick Programming: Supported
Current sensor: Supported
Current scale: 100
Input signal: Dshot300/600

Flywoo GOKU GN745 40A AIO

Price ~ $79.99

Banggood: https://www.banggood.com/25_5+25_5mm-Flywoo-GOKU-GN-F745-2-6S-40A-AIO-…-1791115.html

GetFPV: https://www.getfpv.com/flywoo-goku-gn745-f7-40a-2-6s-blheli32-aio-flight-controller.html

This is powerful AIO flight controller with F745 BGA chip and BLHELI_32 ESC firmware. Board has 5V/9V dual BEC, barometer, black box, on board WS2812 LEDs. Board has pads for 7 (!) complete hardware serial ports and I2C bus. Flywoo GOKU GN 745 AIO takes 2-6S battery input and is capable of outputting the 40A current to motors.  It is the most stuffed AIO board with the F745 MCU on the market. Flywoo even managed to put the LEDs on board!

Release date: 2020-11

Specifications:
MCU: STM32F745 32-bit processor,216MHz, 512Kbytes Flash
IMU: MPU6000 (SPI)
Barometer: BMP280
Onboard LED:WS2812*4
USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
7 hardware UARTS (UART1,2,3,4,5,6,7)
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only.
PPM and PWM receivers are not supported.
Onbord 8Mbytes for Blackbox logging
9V Power Out: 1.5A max
5V Power Out: 2.0A max
3.3V Power Out: 0.5A max
Dimensions: 33.5×33.5mm
Mounting Holes: Standard 25.5/26.5mm square to center of holes
Weight: 8.5g

Built-in 40A BL_32 4in1 ESC
Support BLheli / BLHELI_32
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600,Dshot1200
Input Voltage: 2-6S Lipo
Continuous Current: 40A
Firmware: BLHELI_32

Flywoo GOKU Versatile F4 1S AIO

Price ~ $59.99

Available @ Flywoohttps://flywoo.net/products/goku-versatile-f4-5-in-1-aio

Flywoo whoop AIO board GOKU Versatile F4 5-IN-1. It has F411 MCU, built-in 250mw VTX1S 5A ESC, OSD, Frsky SPI receiver3 serial ports (one is softserial), I2C functionality and 2 x WS2812 LEDs. The weight of the GOKU Versatile F4 AIO board is only 4 grams. One of the lightest whoop boards with integrated VTX and Receiver.

Release date: 2021-08

Features :
Built-in 250mw VTX1S 5A ESCOSD and SPI Frsky receiver
Available 3 serial ports and 12C functionality
Mounting Pattern: 25x25mm, M2
Ultra light weight: 4g
Built-in 2XWS2812 LEDs
Reasonable layout , easy to build

Specifications:
Flight Controller
MCU: STM32F411CEU6 
GYRO: MPU6000
UARTS: 1/2
Soft serial port:1
I2C: SCL/SDA
BEC: 5V
Input Voltage: 1S ( <4.35v)
Firmware: FLYWOOF411FR
Mounting:  25x25mmM2

Onboard 4in1 ESC
MCU: EFM8BB21
Power supply: 1S LiPo/LiPo HV  Current: 5A
Firmware: BLHeli_S
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT 150/300/600

Frsky SPI D8 receiver Version (optional)
SPI BUS receiver Frsky D8 compatible
Compatible Non EU transmitter D8  Channels: 8ch

Onboard 5.8g VTX
Output power: 25mW~250mW switchable
Frequency: 40CH
Frequency: 5.8GHz 5 bands 40 channels(include Race band) IRC ready

GEPRC GEP 12A F4 Flight Controller

Price ~ $39.99

https://www.banggood.com/GEPRC-GEP-12A-F4-V1_1-F411-F4-Flight-Controller-AIO-OSD-BEC-12A-BL_S-2-4S-4In1-ESC-for-RC-Drone-FPV-Racing-p-1474473.html

https://geprc.com/product/gep-12a-f4-flight-controller-12a-esc/

GEPRC was the first to release the 12A whoop sized flight controller. Board accepts 2-4S battery input, outputs 12A (15A burst), has OSD, current sensor. Board also has UART2 pads, inverted and uninverted receiver inputs.

The same board layout was copied or somehow used by many other manufacturers.

Release date: 2019-05

Specifications:

  • Model Name: GEP-12A-F4
  • MCU: STM32F411
  • IMU: MPU6000 gyro/accelerometer (SPI)
  • OSD: BetaFlight OSD w/ AT7456E chip
  • BEC Output: 5V@1A
  • Integrated LC Filter
  • Firmware target: MATEKF411
  • Size: 28.5×28.5mm board,25.5mm mounting holes (M2)
  • Installing Hole: 25.5×25.5mm, M2
  • ESC MCU: BB21F16G
  • Continuous current: 12A
  • Input: 2-4s lipo
  • Supports Dshot600 ,Oneshot,Multishot
  • Current meter: 210
  • Target: G_H_30
  • Weight: 5.6g

GEPRC GEP 20A F4 Flight Controller

Price ~ $59.99

https://www.banggood.com/GEPRC-GEP-20A-F4-AIO-F4-MPU6000-Flight-Controller-OSD-20A-…-1607659.html

https://geprc.com/product/gep-20a-f4-flight-controller/

GEPRC was the second manufacturer to release the 20A whoop sized flight controller in the market. This GEP20A-F4-AIO FC accepts 2-4S battery input,  is rated for 20A continuous current and 30A on peak. The MOSFETs on the board are TOSHIBA TPN2R203NC, that are capable of providing of max 45A of the current.

Release date: 2019-11

Specifications:

  • Model Name: GEP-20A-F4
  • MCU: STM32F411
  • IMU: MPU6000 gyro/accelerometer (SPI)
  • FC Firmware target: MATEKF411
  • OSD: BetaFlight OSD w/ AT7456E chip
  • Current Monitoring: Support
  • Betaflight OSD: Support
  • External Buzzer: Support
  • LED: Support
  • USB Port: MicroUSB
  • BEC Output: 5V@1A
  • Integrated LC Filter
  • ESC MCU: BB21F16G
  • Continuous current: 20A
  • Peak current: 30A
  • Input: 2-4s lipo
  • Supports Dshot600 ,Oneshot, Multishot
  • Current meter: 210
  • Target: G_H_30
  • Size: 32x32mm board, 26.5mm mounting holes (M2)
  • The overall weight is about 7.3g

GEPRC GEP F722 35A Flight Controller

Price ~ $89.99

GEPRC: https://geprc.com/product/gep-f722-35a-aio-f722-fc-35a-2-6s-8bits-bls-esc-26-5mm-m2/

GEPRC GEP F722 35A AIO is the new F722 MCU flight controller with 35A continuous current output. It was introduced with GEPRC Crocodile Baby 5 quadcopter.

Board has 5 full UART ports, can handle 35A continuous current (40A burst), supports the 2-6S lipo battery.

GEPRC GEP F722 35A AIO Pinout diagram:

Release date: TBD
Specifications:
Model Name: GEP-F722-35A AIO
MCU: STM32F722
IMU: MPU6000 gyro/accelerometer(SPI)
Firmware target: GEPRC_F722_AIO
OSD: Betaflight OSD w/ AT7456Ev
UART Ports: R1 T1 / R2 T2 / R3 T3 / R4 T4 / R5 T5
Beeper:YES
LED:YES
USB:Micro USB
BEC output: 5V@1A
Intergrated LC Filter
ESC MCU: 8BB21F16G
Continuous current:35A
MAX current:40A (10s)
Input:2~6S
Supports:Dshot600,Oneshot,Multishot
BlackBox: 16Mb
Traget:G_H_30
Size:32x32mm Board
Installing Hole:26.5×26.5mm,M2
Weight:8.8g

Holybro FETtec Mini 15A AIO

Price ~ $79.99 – 99.99

Holybro: http://www.holybro.com/product/holybro-fettec-mini-aio-15a

Banggoodhttps://www.banggood.com/25_5x25_5mm-Holybro-FETtec-Mini-AIO-2-4S-F3-Flight-Controller-…-1881675.html

Release date: 2021-08

Specifications:
FC: KISS FC firmware
F3 Processor (STM32F303CCT6 @ 72MHz (MPU6000))
Supply voltage 6-18V (2S-4S Lipo voltage)
Dedicated onboard 5V BEC (max 1A)
ESC: Active current limiting @ 15A
Input voltage: 2S-4S
High quality 30V MOSFETs
STM32G071 @ 64MHz
128 kHz Motor PWM
Automatic input signal detection
Dshot 300-2400, PWM, OneShot42/125
OSD: Graphic OSD (STM32)
Full KISS Tuning
Filter (PIDs, Rates, Settings)
LED control (RGB LED, Racewire)
VTX
Live data graphs (Voltage, motor rpm, current, motor temp, gyro values, link quality)
KISS GPS support + live map
Custom graphic pilot logo
Stick overlay
Custom layout

iFlight SucceX-D 20A Whoop F4 AIO Flight Controller

Price ~ $49.99

https://shop.iflight-rc.com/index.php?route=product/product&product_id=1223

https://www.banggood.com/IFlight-SucceX-D-Whoop-F4-Flight-Controller-…-1709071.html

iFlight SucceX-D 20A Whoop AIO is probably the first whoop/toothpick AIO FC board with the dedicated connector for DJI Air digital FPV system. This AIO FC is capable of accepting the 2-5S battery and provides up to 20A (25A burst).

Release date: 2020-05

Specifications:
Size: 30.5*30.5mm
Mounting pattern:25.5*25.5mm/φ3mm
MCU: STM32F411
Gyro: MPU6000
Blackbox: 8MB
BEC output: 5V 2A/10V 2A
INA pad: nR2
Barometer:no
Constant current:20A25A(burst)

Input:2-5S8-25V
Current sensor: yes
BLHeli:BLHeli-S
ESC Telemetry:no
Target: IFLIGHT_F411_PRO
ESC Firmware: G-H-30 BLS

Package Includes:
– SucceX-D Whoop F4 AIO Board× 1
– Capacitor 470uF/16V × 1
– XT30 18awg cable
– Wire harness (plug&play) for DJI Air Unit × 1
– M2 silicon grommets × 4
– M2 damping balls x 4
– M2*8mm Screws x 4

iFlight SucceX Whoop F4 12A Flight Controller

Price ~ $39.99

https://www.iflight-rc.com/index.php?route=product/product&product_id=848

https://www.banggood.com/IFlight-SucceX-Whoop-F4-2-4S-Flight-Controller-AIO-OSD-BEC-Built-in-12A-BL_S-ESC-for-RC-Drone-FPV-Racing-p-1485838.html

The similar layout to GEPRC GEP-12A-F4 flight controller. iFlight has changed the gyro to ICM-20689 and added the sockets for add-on VTX board. Later revision brought the MPU6000 gyro back.

Release date: 2019-05

Specifications:
Name: iFlight SucceX Whoop F4
STM32F411
-Input voltage 2-4S Lipo
-Gyro: ICM-20689MPU6000
2x UART ports
OSD inbuilt
-Blackbox FLASH: 8MB
-BEC: 5V 2A cont.
-Size: 28.5*28.5mm
-Mounting holes: 3mm 25.5*25.5mm
-Weight: 6.1g
-BF target : IFRC/IFF411PRO(STM32F411)
Current Scale: 210

Built-in SucceX Mirco 12A ESC
-Firmware: Blheli_S G-H-30
-Input voltage : 2-4S LIPO
-Continuous current: 12A
-MCU: BB21F16G
-BEC : None
-ESC protocol: pwm, oneshot125, multishot, dshot150, 300, 600, etc.

iFlight SucceX F4 V2 1S 5A AIO FC with Built-in D8 Receiver

Price ~ $56.99

iFlight: https://shop.iflight-rc.com/SucceX-F4-V2-1S-5A-AIO-Whoop-Board-with-Built-in-D8-Receiver-pro1609

Banggoodhttps://www.banggood.com/IFlight-SucceX-F4-V2-Whoop-AIO-Flight-Controller-…-1878186.html

This 1S whoop type flight controller has integrated FrSky D8 receiver and VTX. Board is rated at 5A.

Release date: 2021-07

Specifications:
Size:29*29mm
Mounting pattern: 25.5*25.5mm/φ3mm (half-hole)
Connector:Micro-USB
Weight: 4.8g (with power cable, vtx, and vtx antenna)
MCU:STM32F411
Gyro:MPU6000
Blackbox: no
BEC output:5V 1.2A
INA pad:n uart2
Barometer: no
FC Firmware:MatekF411RX
NOTE: F.PORT protocol RX input support, telemetry not supported.
ESC 
Current: 5A continuous and peak 6A
Current scale: 400
Input:1S
Signal Support: Dshot,Oneshot,Multishot
Current sensor:yes
BLHeli: BLHeli-S
ESC Telemetry: no
ESC Firmware: O_H_05 16.8
VTX:
Input voltage: 5V
Channels: 48CH
Power: PIT/25/50mW
Connector: UFL/IPEX
Protocol: Smartaudio

iFlight Beast F7 45A V1.2 AIO Flight Controller

Price ~ $87.99

iFlight: https://shop.iflight-rc.com/beast-f7-45a-v1-1-aio-mpu6000-25-5×25-5-pro1377

Banggoodhttps://www.banggood.com/25_5+-25_5mm-iFlight-Beast-F7-AIO-2~6S-Flight-Controller-45A…-1779832.html

The iFlight Beast F7 45A is the first toothpick AIO flight controller with F745 MCU in BGA package. This is also the first AIO flight controller with 45A output capability. A lot of UARTS, barometer, black box and connector to DJI Digital FPV system (but no separate BEC for the DJI) are on this board.  iFlight has changed the barometer to DPS310 enlarged the motor solder pads and changed black box size to 16Mb in the version 1.2 of this AIO. Amazing, powerful and feature rich board!

iFlight Beast F7 45A F745 AIO connection diagram: https://shop.iflight-rc.com/image/catalog/product/Beast/Beast-F7-V1.2-Wiring-Diagram.png

Release date: 2020-10

Specifications:

MCU: BGA-STM32F745
OSD: AT7456E
Gyro: MPU6000
Blackbox: 8Mb 16Mb Onboard Flash
BEC Output 5V, 2.5A
Barometer BMP280 DPS310
ESC Current: 45A , 50(Burst)
Voltage: 2-6S
Current Scale 200
Uarts 5
BLHeli: BLheli_S
ESC Telemetry: No
Current Sensor: YES
FC Target: IFLIGHT_F745_AIO 4.2.0
ESC Firmware: BLHeli_S G-H-30 16.9

Dimensions: 32.5*32.5mm
Pattern 25.5*25.5/M3
Connector Micro-USB
Weight 8.5±1g

iFlight Beast H7 55A V2.2 AIO Flight Controller

Price ~ $105.99

iFlighthttps://shop.iflight-rc.com/Beast-H7-V2-55A-AIO-MPU6000-25.5-25.5-pro1588

Banggoodhttps://www.banggood.com/25_5+25_5mm-iFlight-Beast-H7-AIO-2-6S-Flight-Controller-55A-…-1779860.html

The iFlight Beast H7 55A is the first (and the only) toothpick AIO flight controller with H743 MCU in BGA package. This MCU runs on 480MHz operating frequency and has a lot of processing power overhead. iFlight Beast H7 55A is also the first (and the only) AIO flight controller with 55A output capability. A lot of UARTS, precision DPS310 barometer, black box and connector to DJI Digital FPV system (but no separate BEC for the DJI) are on this board. This is the most powerful and unmatched board to the release date!

Main changes from V1 to V2.2:
Circuit design optimized
RPM-filtering can be used with JazzMaverick firmware (BLHeli-M), and JESC.
Gyro sensor is Bosch BMI270

iFlight Beast H7 55A H743 AIO connection diagram: https://cdn.shopify.com/s/files/1/1126/9610/products/Beast-H7-55AAIO-WiringDiagram_3700x.png

Release date: 2020-10

Specifications:

MCU: BGA-STM32H743 , 480MHz
OSD: AT7456E
Gyro: MPU6000
Blackbox: 8Mb 16Mb Onboard Flash
BEC Output 5V, 2.5A
Barometer BMP280 DPS310 BMI270
ESC Current: 55A , 60(Burst)
Voltage: 2-6S
Current Scale 200
Uarts: 5
BLHeli: BLheli_S
ESC Telemetry: No
Current Sensor: YES
FC Target: IFLIGHT_H743_AIO
ESC Firmware: BLHeli_S G-H-30 16.9

Dimensions: 32.5*32.5mm
Pattern 25.5*25.5/M3
Connector Micro-USB
Weight 8.8±1g

iFlight BLITZ F411 1S 5A AIO Flight Controller

Price ~ $69.99

iFlighthttps://shop.iflight-rc.com/BLITZ-F411-1S-5A-Whoop-AIO-Board-with-Built-in-Receiver-Pro1726

Banggoodhttps://banggood.com/25_5x25_5mm-iFlight-BLITZ-F411-F4-1S-5A-Whoop-AIO-Flight-Controller-…-1951266.html

AIO flight controller for tiny whoop with integrated VTX and radio receiver. There are two radio receiver options – with ELRS or with FrSky D8 to choose. ELRS version has on board ceramic tower antenna. VTX power output is 25/50mW. The total weight of the board is 4.4g (w/o VTX antenna).

Release date: 2022-04

Features:
1. Light weight, 4.4-4.8g;
2. BLHeli-S ESC, 5A continuous current;
3. MCU processor of STM32 F411;
4. BMI270 gyroscope;
5. The default frequency of the ESC is 16.8 96K frequency parameters, which can make the flight more efficient;
6. The factory comes with image transmission, no need to add additional fixing methods;
7. onboard SMD antenna/built-in CC2500 SPI receiver, support D8, S-FHSS protocol. Receivers of other protocols can also be welded

Flight controller
External dimensions: 29*29mm
Hole size: 25.5*25.5mm/φ3-half hole
USB Type: Micro-USB
Weight: 4.4-4.8g
MCU: STM32 F411
OSD: AT7456E
Gyroscope: BMI270
BlackBox: NO
BEC: 5V 500mA
INA Pad: n unat2
Barometer: none
WS2812ledStrip: Yes
Beeper: Yes
Firmware target: IFLIGHT_BLITZ_F411RX

ESC:
Current support: 5A (continuous), 6A (instantaneous)
Current ratio: 400
Voltage input: 1S
ESC protocol: Dshot, Oneshot, Multishot
Current sensor: yes
BLHeli:BLHeli-S
Telemetry: none
ESC firmware: O-H-30 BLS16.8

VTX:
Input voltage: 5V
Number of channels: 48CH
Transmit power: PIT/25/50mW
Antenna interface: UFL/IPEX4
Protocol: Smartaudio

NeutronRC F4 1S 5A AIO

Price ~ $40

Aliexpress: https://www.aliexpress.com/item/1005004380944022.html

NeutronRC F4 1S is F411 MCU based flight controller for tiny whoop with integrated ExpressLRS radio receiver. ELRS receiver has on board ceramic tower antenna and ipex connector for external antenna. This board also has 16MB Blackbox flash memory on board. The total weight of the board is 4g (w/o RX antenna).

Release date: 2022-04

Connection diagram:

Specifications:

CPU: STM32F411CEU6 (100MHZ)
IMU: ICM-20689
Built-in Receiver: SPI ExpressLRS 2.4G Receiver antenna:
2.4GHz SMD ceramic antenna or IPX at your choice
Serial Ports: UART1/UART2
Size: 29mm x 29mm
Firmware target: Betaflight: NEUTRONRCF411SX1280
OSD: Built-in BetaFlight OSD
Blackbox: 16MB SPI Flash
Weight: 4g (bare PCB, without wires)
PCB: 6 LAY-2OZ
Onboard RGB programmable LED
BEC: 5V 1.5A
Battery Voltage: 1S/1S HV/(4.2-4.35V)
Current: 5A continuous and peak 6A (3 seconds)
Current sensor: NO
Support BLHeliSuite programmable
Factory firmware: BLHeli_S/Bluejay(O_H_5) Protocol: Dshot150, Dshot300, Dshot600,Oneshot125
Oneshot125, Multishot, PWM

NeutronRC F411 45A 35A 2-6S BLHeIi_S AIO

Aliexpress: https://www.aliexpress.com/item/1005004710362794.html

Price ~ $55 – $65

F411 AIO flight controller for medium sized toothpicks to 5inch quadcopters. There are two options to choose – one with 45A and another with 35A 4in1 ESC.  Board has 3 UARTs (2 hardware an 1 softserial), Barometer, Current sensor and on-board 16MB Blackbox.

Release date: 2022-08

NeutronRC F411 45A AIO Connection Diagram:

Specifications:
MCU: STM32F411CEU6, 100MHz, 512KB Flash
IMU: BMI270 (SPI1) Gyro (rotation CW-90)
OSD: AT7456E (SPI2)
Blackbox: SPI Flash 16M
Baro: Infineon DPS310 (I2C)
3xUarts(1,2,Softserial11)
BEC: 5V 2.0A(Max 2.5A)
Betaflight firmware target: Neutron RCF411AIO
Current sensor (Scale 100) & Voltage sensor (Scale 110)
2x LEDs for FC Status and 3.3V
ESC MCU: EFM8BB21 48MHz, FD6288 3in1 driver
SH1.0-6pin,DJI/Vista straight plug
Toshiba MOS(45A)&Other (35A), low internal resistance and high current
Current: 45A, Max 50A(5S) / 35A, Max 40A(5S)
ESC Firmware: BLHeli_S/Blujey(Type pwm 48K for BMI270)
8-layer 2OZ, 2-order blind via PCB.

NeutronRC F722 45A 2-6S AIO

Price ~ $90

Aliexpresshttps://www.aliexpress.com/item/1005004699530133.html

NeutronRC F722 45A AIO is flight controller for bigger toothpicks or full sized quadcopters. It has 4in1 45A (60A) ESC, 5 UARTs (all hardware), Barometer, Current sensor and on-board 16MB Blackbox.

Release date: 2022-08

NeutronRC F722 45A AIO Connection Diagram:

Specifications:
MCU: STM32F722RE,216MHz,1MB Flash
IMU: BMI270 (SPI1) CW=90
OSD: AT7456E (SPI2)
Blackbox: SPI Flash 16M
Baro: Infineon DPS310 (I2C1), shared with UART3
5xUarts(1,2,3,4,5) & 1x I2C
BEC: 5V 2.0A(Max 2.5A)
Betaflight target: (NeutronRCF722AIO)
Current sensor (Scale 100)&Voltage sensor (Scale 110)
2x LEDs for FC Status and 3.3V
ESCMCU: EFM8BB21 48MHz
FD6288 3in1 driver
SH1.0-6pin,DJI/Vista straight plug
ONSemi Industrial MOS, low internal resistance and high current
Current 45A ,Max 60A(5S)
ESC Firmware: BLHeli_S/Blujey(Type pwm 48K for BMI270)
8-layer 2OZ, 2-order blind via PCB.
Input Voltage: 2-6S 5-36V
Mounting: 25.5×25.5mm w/M3 Grommets
Size: 34x34x7mm
Weight: 8g

NeutronRC F7 55A 2-6S AIO

Price ~ $112

Aliexpress: https://www.aliexpress.com/item/1005004380897762.html

NeutronRC F7 55A 2-6S AIO is powerful flight controller for serious toothpick and quadcopters. It has two different Bosch BMI-270 and Invensense ICM-20689 gyros IC’s. STM32F745 MCU with 1Mb flash drives 4in1 55A (65A) ESC, 7 UARTs (all hardware), Barometer, Current sensor and big on-board 125MB Blackbox.

Release date: 2022-09

NeutronRC F7 55A AIO Connection Diagram:

Specifications:
MCU: STM32F745VGH6, 216MHz, 1MB Flash
IMU: Two gyros – BMI270 (SPI1) CW=270 & ICM-20689 (SPI2)
OSD: AT7456E (SPI4)
Blackbox: SPI Flash 125Mb (SPI3)
Baro: Infineon DPS310 (I2C1)
7xUarts(1,2,3,4,6,7,8) & I2C (I2C2) shared with UART3
Dual BEC: 5V 2.0A(Max 2.5A) & 12V 1.5A(Max 2.0A)
Betaflight target: (NeutronRCF7AIO)
Current sensor (Scale 100)&Voltage sensor (Scale 110)
4x LEDs for FC Status and 3.3V/5V/VBAT
ESCMCU: STM32G071GB 64MHz
FD6288 3in1 driver
SH1.0-6pin,DJI/Vista straight plug
Infineon FDM8010DC MOSFET
Current 55A ,Max 65A(5S)
ESC Firmware: BLHeli_32
8-layer 2OZ, 2-order blind via PCB.
Input Voltage: 2-6S, max 36V
Mounting: 25.5×25.5mm w/M3 Grommets
Size: 34x34x7mm
Weight: ~10g

NeutronRC H743 45A 2-6S AIO

Price ~ $118

Aliexpresshttps://www.aliexpress.com/item/1005004699423262.html

NeutronRC H743 45A 2-6S AIO is the most powerful flight controller from NeutronRC for serious toothpick and quadcopters. It has two Bosch BMI-270 gyro IC’s, with orientation shifted in 90 degrees  working simultaneously. STM32FH743MCU with 2Mb flash memory space for firmware. NeutronRC H743 45A 2-6S AIO features 4in1 45A (65A) ESC, 7 UARTs (all hardware), Barometer, Current sensor and enormously sized on-board 512MB Blackbox.

Has firmware targets in Betaflight (NeutronRCH743AIO) and INAV (NeutronRCH7BT)

Release date: 2022-09

NeutronRC H743 45A AIO Connection Diagram:

Specifications:
MCU: STM32H743VIH6, 480MHz, 2MB Flash
IMU: TwinG – two gyros – BMI270 (SPI1) CW=90 & BMI270 (SPI4) CW=0
OSD: AT7456E (SPI2)
Blackbox: SPI Flash 512Mb
Baro: Infineon DPS310 (I2C1)
7xUarts(1,2,3,4,6,7,8) & I2C (I2C2)
Dual BEC: 5V 2.0A(Max 2.5A) & 12V 1.5A(Max 2.0A)
Betaflight target: NeutronRCH743AIO
INAV target: NeutronRCH7BT
Current sensor (Scale 100)&Voltage sensor (Scale 110)
4x LEDs for FC Status and 3.3V/5V/VBAT
ESCMCU: STM32G071GB 64MHz
FD6288 3in1 driver
SH1.0-6pin,DJI/Vista straight plug
Infineon FDM8010DC MOSFET
Current 45A ,Max 60A(5S)
ESC Firmware: BLHeli_32 (use pwm 64K for BMI270)
Input Voltage: 2-6S, max 36V
Mounting: 25.5×25.5mm w/M3 Grommets
Size: 34x34x7mm
Weight: ~10.8g

SPCMaker Whoop F4 25A Flight Controller

Whoop AIO board by SPCMaker supporting 2-4S battery input and capable of 25A output. It was the most powerful AIO whoop flight controller when it was released.

SPCMaker Whoop F4 25A FC has all the useful features – MPU6000 via SPI, Betaflight OSD, current sensor, inverted and uninverted RX inputs, RX2/TX2 pads and even I2C interface (SDA/SCL). SPC Maker flight controller has also programmable LED and Buzzer pads.

Despite the manufacturer stating that the board has motor sockets with gold plated pins, I think these little motor sockets can really melt under the full rated current 25A! And not talking about 40A… If only the SPC Maker would have made motor solder pads – it would have been the perfect board for power toothpicks (3-4-5 inch) and lightweight 5″ quads.

Price ~ $55.99

https://www.banggood.com/25_5x25_5mm-SPCMaker-Whoop-F411-F4-OSD-Flight-Controller-…-1702948.html

Release date: 2019-12

Specifications:
Brand Name: SPCMaker
Item Name: F4 OSD Flight Controller Built-in 25A 4in1 ESC
Size: 31.4×31.4mm
Mounting Hole: 25.5×25.5mm 
Weight: 7g
CPU: STM32F411CEU6 (100MHZ)
MPU: MPU6000 ( SPI)
Betaflight firmware targer: SPCMAKERF411 (SPCM)
Built-in Betaflight OSD ( AT7456E)
Built-in Current Sensor (Current Coefficient Amp Meter Scale: 300)
– Support WS2812 LED
– Support DSMX/DSM2; TBS Crossfire, IBUS, SBUS Receiver
Input Voltage: 2-4S Lipo
Con. Current: 25A
Burst Current: 40A
Firmware Support: BLHELI_S/JESC
Firmware Version: BLHELI_S (G_H_30)
Motor Connector: 1.25mm 3P spacing Straight Pin Holder
– Support PWM, Oneshot42, Oneshot125, Multishot, Dshot150 and Dshot300, Dshot600

Package Included:
1x SPCMaker F4 Flight Controller Built-in 25A ESC Board

SPCMaker Galloping F411 30A Flight Controller

“Toothpick” type AIO board by SPCMaker supporting 2-6S battery input and capable of up to 30A output. This board has motor solder tabs, 2 full UARTS, one softserial and even I2C port.

Price ~ $45.00

https://www.spcmaker.com/products/galloping-f411-30a-aio

Release date: 2020-09

Specifications:
Name: SPCMaker Galloping F411 OSD Flight Controller Built-in 30A 4in1 ESC
Size: 33x33mm
Mounting Hole: 25.5×25.5mm 
Weight: 7.8g
CPU: STM32F411CEU6 (100MHZ)
MPU: MPU6000 ( SPI)
Betaflight firmware target: MATEKF411 (SPCM)
Built-in Betaflight OSD ( AT7456E)
Built-in Current Sensor (Current Coefficient Amp Meter Scale: 300)
– Support WS2812 LED
– Support DSMX/DSM2; TBS Crossfire, IBUS, SBUS Receiver
Input Voltage: 2-6S Lipo
Con. Current: 30A
Burst Current: 40A
Firmware Support: BLHELI_S/JESC
Firmware Version: BLHELI_S (Q_H_20)
– Support PWM, Oneshot42, Oneshot125, Multishot, Dshot150 and Dshot300, Dshot600

SPCMaker R66 F4 1S 6A AIO Flight Controller

SPCMaker R66 is “whoop” type AIO board by SPCMaker supporting 1S battery input and capable of up to 6A continuous (8A burst) output. This board has F411 MCU, One full UART and one TX pad, inverter for SBUS input, current sensor, LED, Buzzer pads. The board

Estimated Price: $41

Availability – not available @ the moment.

Release date: 2021-10 (?)

Specifications:
Name: SPCMaker R66 F4 1S AIO FC
Mounting Hole: 25.5×25.5mm 
Weight: 2.8g
CPU: STM32F411CEU6 (100MHZ)
MPU: MPU6000 ( SPI)
Betaflight firmware target: MATEKF411RX (?)
Built-in Betaflight OSD ( AT7456E)
Built-in Current Sensor (Current Coefficient Amp Meter Scale: 400)
– Support WS2812 LED
– Support DSMX/DSM2; TBS Crossfire, IBUS, SBUS Receiver
BEC Output: 5V@1.2A
Input Voltage: 1S Lipo
Con. Current: 6A
Burst Current: 8A
Firmware Support: BLHELI_S/JESC
Firmware Version: BLHELI_S (O_H_5)
– Support PWM, Oneshot42, Oneshot125, Multishot, Dshot150 and Dshot300, Dshot600

Price: ~ $115.99

Available @ SpeedyBee: https://www.speedybee.com/speedybee-f745-35a-bls-25-5×25-5-aio-flight-controller

GetFPV: https://www.getfpv.com/speedybee-f745-aio-flight-controller-f745-fc-35a-blheli-s-3-6s-esc.html

The SpeedyBee F745 AIO includes an F745 flight controller and a 35A ESC. Featuring a BMP280 barometer, OSD, 8MB Memory Blackbox, and MPU600 Gyro.

This AIO board has 8 layer PCB and weight 10.1 grams.

Release date: 2022-08

SpeedyBee F745 35A BLS AIO User Manual: https://d18j4b7oq8p8jg.cloudfront.net/…/…_F745_35A_AIO_EN.pdf

Specifications:
Product: SpeedyBee F745 35A BLS AIO
Power Input: 3S – 6S Lipo
Mounting: 25.5 x 25.5mm, 3mm hole diameter
Dimension: 36.5mm(L) x 36.5mm(W) x 7mm(H), recommended for quads at 3.5″ or above
Weight: 10.1g
FC
MCU: STM32F745
IMU(Gyro): MPU6000
USB Connection: Need to solder a USB TYPE-C module to D+,D-,GND pads.
Barometer: BMP280
OSD: Supported
BLE Bluetooth: Supported. Used for parameter configuration
Flash FC Firmware Wirelessly: Supported
Download/Analyze Blackbox: Supported
DJI Air Unit 6-pin Connector: Built-in.
Flash(for BlackBox): 8MB
Current Sensor: Supported. Scale=256
BetaFlight Camera Control Pad: Yes(CC pad)
5V Output: 4 groups of 5V output. The total current load is 2.5A.
9V Output: None
3.3V Output: Supported. Up to 500mA current load.
ESC Signal Pads: M1 – M4
UART: Full UART * 4(UART1, UART2, UART3,UART4)
ESC Telemetry UART: None
I2C: Supported.
LED Pad: Used for WS2812 LED
Buzzer: BZ+ and BZ- pad used for 5V Buzzer
BOOT Button: Used to enter DFU mode
RSSI Input: Not supported
SmartPort: Use any TX pad of UART for the SmartPort feature.
Supported Flight Controller: BetaFlight(Default)
Firmware Target Name: SPEEDYBEE F745AIO
ESC
Power Input: 3-6S LiPo
Continuous Current: 35A * 4
Burst Current: 45A(5S)
ESC Protocol: DSHOT300/600
Power Output: VBAT
Current Sensor: Supported(Sacle=256)
Firmware: BLHeli_S JH40

Skystars KARMAM F411 AIO Flight Controller

https://www.banggood.com/Skystars-KARMAM-F411-AIO-MPU6000-5V1_5A-BEC-15A-2-4S-25_5mm-For-FPV-Racing-RC-Drone-p-1593561.html

Price ~ $39.99

The same slightly altered layout of the GEPRC GEP-12A board. Just added solder pads for motors. Although the MosFET’s are the same as on GEPRC GEP-12A board (AON7934), the Skystars  have rated this board as capable for 15A continuos current to motors. Looks like the Skystars have overrated their board.

Release date: 2019-11

Specifications:
Brand Name: Skystars F411 AIO
MCU: STM32F411
IMU: MPU6000 gyro/accelerometer (SPI)
OSD: BetaFlight OSD w/ AT7456E chip
BEC Output: 5V@1.5A
Integrated LC Filter
Continuous current: 15A
Input: 2-4s lipo
Supports pwm, Oneshot125, Multishot, Dshot150, Dshot300, Dshot600
Size: 32.5×32.5mm board,25.5mm mounting holes (M2)
Installing Hole: 25.5×25.5mm, M2
Weight: 5.2g

Team BlackSheep Podracer AIO

TBS: https://www.team-blacksheep.com/products/prod:tbs_podraceraio

Price ~ $69.95

TBS partnered with Zeez to make this toothpick AIO. TBS Podracer AIO board is designed to accommodate  TBS Pro32 Nano VTX and TBS Crossfire / Tracer Nano RX with direct pin-header installation. The result is a clean, compact and lightweight AIO stack in your build.

The Podracer AIO FC is equipped with F411 MCU + MPU6000 gyro and the ESC is capable of 30A current running BLHeli32.

Specifications:

  • Mounting holes: 25.5×25.5 mm / M2 holes
  • Crossfire/Tracer RX CH1&2 > Uart 2  /  Pro32 Nano VTX > Uart 1 / Uart 1(RX) – unavailable.
  • Up to 6S input
  • 5V BEC up to 1.2A continuous
  • STM32F411 MCU (Support BetaFlight, EmuFlight)
  • MPU6000 Gyro/ACC
  • OSD chip Onboard (AT7456E)
  • 2 UARTs
  • LC Filter for 5V VTX and Camera
  • Direct solder connection for TBS Nano RX and TBS Unify Pro32 Nano
  • Support programmable LED like WS2812 etc
  • Built-in current sensor

ESC:

  • Signal support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
  • Input voltage: 2S-6S Lipo
  • Continuous current: 30A
  • Peak current: 35A
  • ESC firmware: BLHELI_32
  • PWM Frequency Range: 24KHz up to 96KHz

TuneRC (FPVCycle) EZ F4 1-2S AIO

TuneRChttps://www.tunerc.com/product/ez-1-2s-aio/

FPVCycle: https://fpvcycle.com/products/fpvcycle-1s-aio-with-tbs-crossfire-tbs-pro32-nano-vtx

Price ~ $55.99

TuneRC EZ 1-2S AIO (also sold as FPVCycle 1S AIO) is toothpick board with big pads for easy soldering. This board has horizontal USB socket and bigger size so it will not fit into the most whoop frames. ESCs are running BlueJay firmware and are capable of outputting up to 7A of current.

Release date: 2021-09

Specifications

  • FC MCU: STM32F411 (Cortex®-M4 100MHz)
  • Built-in OSD: AT7456E
  • Buit-in IMU: MPU6000
  • ESC MCU: EFM8BB21 ( 8bit 50MHz)
  • UART: UART1 (used for vtx by default), UART2 (used for rx by default, supports SBUS)
  • Input Voltage: 2.20-10.0V( 1-2S LIPO/LIHV )
  • Power Output: 5V1.5A / 3.3V250mA (3.3V only used for rx)
  • Recommended Maxium Motor Size: 13mm
  • FC Target: FPVCYCLEF401
  • ESC Firmware: Bluejay F-H-70
  • Size: 32.4mm x 32.4mm (widest size)   30.2mm x 30.2mm (narrowest  size)
  • Mounting Holes Pattern: 25.5 x 25.5mm   Room for M3.5 grommets to make M2 mount
  • Weight: 4.7g

TuneRC Poly F405 2S-4S AIO

TuneRC: https://www.tunerc.com/product/poly-f405-2s-4s-aio/

FPVCycle:

Price ~ $63.50

TuneRC Poly F405 2S-4S AIO is another toothpick FC from TUNERC. ESCs are running BlueJay firmware and are capable of outputting up to 20A of current. Board has outputs for up to 8 motors (onboard ESC has 4 motor drivers, so you need to add 4 more ESCs for 8 motor setup). Poly F405 2S-4S AIO features 5 UART ports and also has solder pads for I2C, LED strip and buzzer.

Release date: 2022-07

TuneRC Poly F405 2S-4S AIO FC connection diagram:

Specifications

  • FC MCU: STM32F405RGT6( Cortex®-M4 168Mhz )
  • Built-in OSD: AT7456E
  • Built-in IMU: BMI270
  • Built-in 4MByte Blackbox
  • Built-in Current Meter
  • ESC MCU: EFM8BB21 ( 8bit 50MHz )
  • UART: UART1 ( for VTX by default ), UART2, UART3, UART4( for the receiver by default, supports SBUS ), UART5
  • Other interfaces: IIC ( IIC2 ) , LED_Strip, Buzzer
  • The through holes for power lead: big enough to fit 16AWG wire
  • 8 Motor Outputs ( The onboard esc have been used for 4 motor outputs. You can add 4 external esc if you want to use the other 4 motor outputs )
  • Input Voltage: 6.50-20.0V( 2S-4S LIPO/LIHV )
  • Power Output: 5V 2A
  • Continuous Current: 20A
  • Peak Current: 28A
  • FC Target: TUNERCF405
  • ESC Firmware: Bluejay P-H-25
  • A 35V 220uf capacitor is included. A 35v 220-470 uf capacitor with low ESR is recommended if you want to swap the default one.
  • Size: 33mm x 33mm
  • Mounting Holes Pattern: 25.5 x 25.5mm   Room for M3.5 grommets to make M2 mount
  • Weight: 5.8g

HAKRC F4126 20A/35A Whoop AIO FC

20A: https://www.banggood.com/HAKRC-F411-20A-AIO-26mm-…-1711816.html

35Ahttps://www.banggood.com/HAKRC-F411-35A-2-6S-AIO-…-1737041.html

Price ~ $34.99 – 49.99

The F4126 is HakRC’s whoop style AIO flight controller with ESC board for ultralite quads and toothpicks. It available in two options capable of 20A and 35A continuous current (25A and 40A burst). There is a confusion on the max battery input voltage as one source says 5S max while other says 6S.
This FC features a Barometer which is rare to see in this type of flight controller.

Release date: 2020-07

Features:
1. PCB adopts high-end 8-layer 2oZ thickened copper skin, which has stronger over-current capability and good heat dissipation.
2. MOS adopts imported 30V high current resistance mos, long life and strong load capacity.
3. industrial-grade LDO, high temperature resistance.
4. high-quality Japanese Murata capacitors, strong filtering performance

Flight control specifications:

CPU: STM32F411CEU6
IMU: MPU6000
OSD: AT7456E
Barometer: BMP280
LED: Support WS2812 and other programmable
Sensor: Built-in current sensor
Firmware version: betaflight_4.1.1_MATEKF411
Receiver: Frsky/ Futaba/ Flysky/ TBS Crossfire/ DSMX:DSM2 receiver
Currrent output: 20A/35A
Battery input: 2-5S (6S?)
Size: 31x 31.mm (26.5×26.5mm mounting hole)
Net weight: 7g

ESC parameters:
Protocol support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 2S-5S Lipo
Continuous current: 20A
Peak current: 25A
Firmware version: BLHELI _S (G- H-30)

HAKRC F7226 40A AIO FC

Banggoodhttps://www.banggood.com/25_5x25_5mm-HAKRC-F722-F7-Flight-Controller-AIO-40A-…-1921353.html

Price ~ $72.50

The F7226 is the first HakRC toothpick style AIO flight controller with F722 MCU. It outputs 40A continuous current and 50A burst.

Release date: 2020-12

HAKRC F7226 40A AIO FC connection diagram:

Specifications:
Brand: HAKRC F7226 FC Built-in 40A BLHELI_ S 2-6S AIO ESC
Ø Flight control parameters:
CPU: STM32F722RET6
IMU: MPU6000
OSD: AT7456E
Barometer: integrated
BEC: 5V/3A
UARTS: 5
LED: Support WS2812 and other programmable
Sensor: Built-in current sensor
Flight control firmware version: HAKRC F722D
Receiver: CRSF / Frsky/ Futaba/ Flysky/
TBS Crossfire/ DSMX: DSM2 receiver
Ø ESC parameters:
Protocol support: PWM, Oneshot125, Oneshot42,
Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 2S-6S Lipo
Continuous current: 40A
Peak current: 50A
Current meter proportional value: 450
Firmware version: BLHELI _S (G- H-30)
Size: 32*32mm (25.5mm-26.5mm mounting hole)
Product net weight: 7g

HIFIONRC AIO F7 Flight Controller OSD Built-in 25A/45A Blheli_S 2-4S

25Ahttps://www.banggood.com/HIFIONRC-AIO-F7-Flight-Controller-OSD-Built-in-25A-…-1716227.html

45Ahttps://www.banggood.com/HIFIONRC-AIO-F7-Flight-Controller-OSD-Built-in-45A-…-1716359.html

Price ~ $42.99 – $57.99

One of the first (actually the second one) flight controllers with F7 MCU, and definitely the first one to offer AIO FC with 25A and even 45A versions. The difference between two versions is only FETs ratings. HIFIONRC AIO F7 board has 5 full UARTS.

Release date: 2020-08

Specifications:
Item name: HIFIONRC AIO F7 Flight Controller OSD Built-in 25A Blheli_S 2-4S 4 In 1 Brushless ESC
CPU: STM32F722_Coretx-M7
MPU: MPU6000 ( SPI)
Firmware: BETAFLIGHT_HIFIONRC F7 4.2
Built-in Betaflight OSD ( AT7456E)
Built-in Current Sensor
Support WS2812 LED
Con. Current: 25A/45A
Input Voltage: 2-4S Lipo
ESC Firmware: BLHELI_S GH30
Support PWM, Oneshot42, Oneshot125, Multishot, Dshot150 and Dshot300, Dshot600
Size: 33x33mm
Mounting Hole: 25.5×25.5mm
Weight: 7.8g

HGLRC Zeus5 AIO 1-2S F411 Flight Controller

Price $50.99

HGLRChttps://www.hglrc.com/collections/aio/products/hglrc-zeus5-aio-1-2s-f411-flight-controller-5a-bl_s-4in1-esc

Banggoodhttps://www.banggood.com/HGLRC-Zeus5-AIO-1-2S-F411-Flight-Controller-5A-BL_S-4in1-ESC-with-WiFi-…-1802359.html

The first (and the only) whoop flight controller with Bluetooth MSP connection. You can connect this FC remotely via Bluetooth with the Betaflight Configurator. This board is designed for 1-2S tiny whoops, delivering up to 5A constant current to the motors. The Crossfire Nano or ExpressLRS receiver can be mounted directly on the board with pin headers. The weight of the board is 4.2 grams.

The things I might miss in this AIO flight controller are Current sensor missing and the USB socket could be optional (solder pads) for weight saving, as you have remote connection already.

HGLRC Zeus5 Connection diagram:

Release date: 2020-07

MCU: STM32F411
Input Voltage: 1-2S
FC Firmware: BF HGLRCF411 (HGLR)
ESC Firmware: BLHeli_S
Gyro: MPU6000
OSD: Support
BEC: 5V/1A
LED: Support
BlackBox: NO
UARTS: 2
5A BL_S 4in1 ESC
Constant Current: 5A
Installing Hole: 25.5X25.5mm.M2
Dimensions: 41.5×41.5mm
Weight: 4.2g

HGLRC Zeus5 FR AIO 1-2S F411 Flight Controller

Price $55.99

HGLRChttps://www.hglrc.com/collections/new-arrivals/products/hglrc-zeus5-fr-aio-1-2s-f411-flight-controller-5a-bl_s-4in1-esc-frsky-spi-rx

Banggood: –

This flight controller is almost the same as HGLRC Zeus5 (see above) but also very different. HGLRC removed the Bluetooth connectivity and installed the integrated SPI FrSky receiver instead. The 8Mb blackbox and BMP280 Barometer were added also. This board is designed for 1-2S tiny whoops, delivering up to 5A constant current to the motors. Because of the integrated SPI receiver you get 2 full free UARTS. The weight of the board is 4.3 grams.

Still the Current sensor is missing.

HGLRC Zeus5 FR connection/wiring diagram:

Release date: 2021-08

MCU: STM32F411
Input Voltage: 1-2S
FC Firmware: ZEUSF4 FR (HGLR)
ESC Firmware: BLHeli_S
Gyro: MPU6000
OSD: Support
BEC: 5V/1A
LED: Support
BlackBox: 8Mb
Barometer: BMP280
Frsky SPI Receiver
Protocol: FRSKY_D8 / Frsky D16
UARTS: 2
ESC Firmware: S-H-90
Constant Current: 5A
Peak Current: 6A(5 Sec)
Support Protocols: DShot600/300/150/Oneshot125/42,MultiShot
Installing Hole: 25.5X25.5mm.M2
Dimensions: 41.5×41.5mm
Weight: 4.3g

HGLRC Zeus10 AIO 2-6S F411 Flight Controller

Price $44.99

HGLRChttps://www.hglrc.com/products/hglrc-zeus10-aio-fpv-racing-drone-2-6s-f411-flight-controller-10a-bl_s-4in1-esc

This flight controller has the same size and format as HGLRC Zeus5, Zeus5 FR (see above).  This board is designed for 2-6S battery input, delivering up to 10A constant current to the motors. Zeus10 AIO has 3 UART ports (2 hardware and one softserial). The weight of the board is 5.1 grams.

And at last this board has Current sensor on board.

HGLRC Zeus10 connection/wiring diagram:

Release date: 2021-11

Specifications:
Item Name: ZEUS10 AIO
Input Voltage: 2-6S Lipo
FC Firmware: ZEUSF4EVO
CPU: STM32F411
MPU: MPU6000
BEC: 5 V/2A
UARTS: 3
OSD: Support
BlackBox: 8M
Built-in Current Sensor

10A BL_S 4in1 ESC
ESC Firmware: P_H_10
Constant Current: 10A
Peak Current: 15A5 Sec
Support Protocols:DShot600/300/150/Oneshot125/42,MultiShot

Usage: for 65mm-200mm Frame Kit
Installing Hole: 25.5X25.5mm.M2
Size: 32.5×32.5mm
Weight: 5.1g

HGLRC Zeus25 AIO V2 3-6S F722 Flight Controller

Price $64.99

HGLRChttps://www.hglrc.com/products/hglrc-zeus25-v2-aio-fpv-racing-drone-3-6s-f722-flight-controller-25a-bl_s-4in1-esc

HGLRC Zeus25 The most powerful toothpick AIO FC from HGLRC.  This board is designed for 3-6S battery input, delivering up to 25A constant current and up to 30A burst to the motors. Zeus25 AIO has 5 UART ports. The weight of the board is 9.1 grams.

This is the second generation of the Zeus25 AIO. HGLRC has added the current sensor and 8Mb BlackBox to this board. Zeus25 has 6 pin connector for easy DJI FPV system installation.

HGLRC Zeus25 connection/wiring diagram:

Release date: 2021-11

Specifications:

Item Name: ZEUS25 V2 AIO
Input Voltage: 3-6S Lipo
FC Firmware: ZEUSF722 AIO
CPU: STM32F722 RET6
MPU: MPU6000
BEC: 5V/2A
UARTS: 5
OSD: Support
BlackBox: 8M
Built-in Current Sensor

25A BL_S 4in1 ESC
ESC Firmware: F_H_40
Constant Current: 25A
Peak Current: 30A5 Sec
Support Protocols:DShot600/300/150/Oneshot125/42,MultiShot

Usage:for 100mm-250mm Frame Kit
Installing Hole: 25.5X25.5mm.M2
Size: 34.5×34.5mm
Weight: 9.1g

JHEMCU Play F4 1-2S AIO Whoop FC

Price $26.99 $40.99

Banggood: https://www.banggood.com/25_5x25_5mm-JHEMCU-Play-F4-Whoop-Flight-Controller-AIO-…-1475842.html

One of the cheapest and one of the oldest brushless whoop boards on the market. Was released years ago, and still manufactured in year 2021. Supports 1-2S battery input, outputs up to 5A (7A burst), but make sure you add the capacitor on the battery leads if you are planning to use 2S.

Release date: 2019

Specifications:

Item Name: JHEMCU Play F4 Flight Controller Built-in 5A 4In1 ESC
Board Size: 28.5×28.5mm
Screw Hole Spacing: 24.5×24.5mm ( M3)
Board Weight: 3g

F4 Flight Controller
CPU: STM32F411CEU6
Sensor: MPU6000 Triaxial accelerometer/  Triaxial Gyroscope ( SPI Connection)
Input Voltage: 1-2S Lipo
BEC: 0.5A ( 1S ) ; 1.5A ( 2S )
Built-in OSD interface
– Support Voltage Detection
– Support LED Strip
– Support Smart Audio OSD Control
– Support Buzzer
– Support Compatible PPM, SBUS, IBUS, DSM2/DSMX Receiver

5A ESC:
Input Voltage: 1-2S
Con. Current: 5A
Peak Current: 7A ( 2S)

Note: There is a recommendation to solder a 16V 220UF capacitor on the side of power cable for reliability, especially if you are using 2S battery.

JHEMCU SH50A F4 2-3S AIO Whoop FC

Price $33.99

Banggood:  https://www.banggood.com/JHEMCU-SH50A-F4-OSD-2-3S-Flight-Controller-…-1699429.html

Another cheap brushless whoop board from JHEMCU. This board supports 2-3S battery input, outputs up to 5A (7A burst).

Release date: 2019

Specifications:

Name: JHEMCU SH50A
CPU: STM32F411CEU6
Sensor: MPU-6000 3-axis accelerometer/3-axis gyroscope (SPI connection)
Input Voltage: 2-3S Lipo (DC 7.4-12.6V)
BEC: 5V 2.5A
Black Box: 8MB
Built-in OSD interface
Led_Strip interface
BUZZER buzzer interface
Support PPM, SBUS, IBUS, Spektrum DSM2/DSMX, 1024/2048 Receiver
UART2: TX2 (for image transmission), RX2
UART1: TX1, RX1 (for receiver)
Three sets of BEC output pads
Built-in voltage detection and current sensor
Board Size: 28.5×28.5mm
Screw hole spacing: 24.5×24.5mm, M3
Board Weight: 3.3g
5A BLheli_S 4in1 Brushless ESC
Con. Current: 5A
Burst Current: 7A ( for 2 Seconds)
Factory firmware: S_H_50_REV16_7.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM

JHEMCU GHF411 Pro AIO 25A/35A flight controller

35Ahttps://www.banggood.com/Upgrade-25_5x25_5mm-JHEMCU-GHF411AIO-Pro-…-1652742.html

Price $38.50

Updated GHF411 Pro AIO board from JHEMCU. Current output was increased from 20A to 25A and from 30A to 35A from the previous version. Board now includes I2C port (SCL/SDA pads) and 8Mb black box flash. Also this board has dual BEC 9V/2A,  5V/2.5A so the Caddx Vista module can be powered from the FC. Motor solder pads now are big enough for easy soldering.

Release date: 2020-09

Specifications:

Power Supply: 2-6S
Item Name: F4 OSD Flight Controller Built-in 25A/35A 4in1 ESC
Size: 32.5×32.5mm
Mounting Hole: 25.5×25.5mm
Weight: 7.3g
CPU: STM32F411CEU6 (100MHZ)
MPU: MPU6000 ( SPI)
Firmware: Betaflight FLYWOOF411.HEX
Built-in Betaflight OSD ( AT7456E)
BEC Output(2 Independant):  9V/2A,  5V/2.5A
Ports: UART1, UART2
Receiver: SBUS,IBUS,DSM2,DSMX ,TBS (UART2)
Black box: 8MB
Built-in Current Sensor
Support WS2812 LED Strip
Input Voltage: 2-6S LiPo
ESC Current: 25A/35A
Firmware: BLHELI_S G-H-30.HEX
– Support  PWM, Oneshot42, Oneshot125, Multishot, Dshot150 and Dshot300, Dshot600

JHEMCU GHF405 Pro AIO 25A/45A flight controller

25Ahttps://www.banggood.com/25_5x25_5mm-JHEMCU-AIO-F405-PRO-3-6S-F4-Flight-Controller-…-1842858.html

45Ahttps://www.banggood.com/25_5x25_5mm-JHEMCU-AIO-F405-PRO-3-6S-F4-Flight-Controller-…-1842864.html

Price $56.99 – 61.99

Updated GHF405 Pro AIO board from JHEMCU. Current output is the same for 25A board, but was increased from 35A to the whooping 45A in comparison to the previous version. Board now includes pads for 5 UARTS (4 UARTS on previous board) and now includes 8Mb black box flash. Also this board has dual BEC 5V/2.5A and 10V/2A so the Caddx Vista\Air module can be powered from the FC. GHF405 Pro also has barometer on board and the connector for direct connecting the Caddx/DJI Air unit.

Release date: 2021-05

Specifications:
Name: JHEMCU AIO F405 PRO 25A/45A ESC Board
Weight: 7.1 grams
Size: 33* 33mm (25.5mm mounting hole)
Flight Controller
CPU: STM32F405
Sensor: MPU6000 (SPI connection)
Firmware version: Betaflight JHE405
Black box: support
Barometer: Support
OSD: Support
IIC: Support
UART: support, UART1: receiver, UART6: DJIVTX/IRC/Smart Audio
BEC: BEC 5V/2.5A and 10V/2A
DJIVTX: Support, reserved special socket, equipped with plug wire.
Receiver: SBUS, IBUS, DSM2, DSMX, TBS, etc.
Support WS2812 programmable LED
Support buzzer
Built-in voltage and current sensors
ESC:
Continuous current: 25A/45A BLHELI_S
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 3S-6S Lipo
Firmware: BLHELI_S G_H_30_REV16_7.HEX

JHEMCU GH743 AIO 40A flight controller

Banggoodhttps://www.banggood.com/30_5x30_5mm-JHEMCU-GH743-AIO-3-6S-Flight-Controller-…-1888189.html

Price $87.99

GH743AIO board from JHEMCU has the fast STM32H743 MCU, running on 480MHz. It is the second toothpick AIO board with H743 MCU in BGA package on the market. Current output is impressive 40A. Board includes pads for 7 UARTS (!) and has 8Mb black box flash. This board has dual BEC 5V/2.5A and 10V/2.5A so the Caddx Vista\Air module can be powered from the FC. GH743 also has BMP280 barometer on board and the connector for direct connecting the Caddx/DJI Air unit. JHEMCU added USB ESD (Electro Static Discharge) protection chip on board.

JHEMCU GH743AIO connection diagram.

Release date: 2021-09

Specifications:

CPU: STM32H743
Sensor: MPU6000
OSD: AT7456E
Barometer: BMP280
IIC: Support
Black box: 8MB
BEC: 5V/2.5A, 10V/2.5A
HDVTX: DJI VTX->UART6, reserved dedicated socket, equipped with plug wire
UART: 7 UARTS (actually 6.5 UARTS)
UART list: UART1, UART2, UART3, UART4, UART6, UART7, UART8
USB: micro USB
Mounting size: 25.5*25.5MM 
Receiver: ELRS (CRSF), TBS (CRSF), SBUS, IBUS, DSM2, DSMX
Support WS2812 and other programmable LEDs
Support buzzer
Built-in voltage and current sensors
Weight: 7.5 grams

ESC Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 3S-6S Lipo
Continuous current: 40A
Firmware: BLHELI_S, target  G_H_30_REV16_7.HEX

JHEMCU RuiBet F4 1S-2S AIO flight controller

Aliexpress: https://www.aliexpress.com/item/1005003842566799.html

Price $49.00

JHEMCU RuiBet F4 1S-2S AIO is simple whoop type AIO board with F411 MCU and MPU-6000 gyro. AIO works on 1S and 2S battery and is capable of outputting up to 12A current to motors. There are two UART ports, I2C and place for barometer on the board (not populated on the photo). AIO FC board weights 4.4 grams.

JHEMCU RuiBet F4 1S-2S AIO connection diagram.

Release date: 2022-03

Specifications:
CPU: STM32F411
Gyroscope/Accelerometer: MPU6000
OSD: AT7456E
Barometer: yes
Black box: None
IIC: support
BEC: 5V
UART: UART1,UART2
USB: micro-usb
Size: 25.5×25.5MM M2
Receiver: ELRS,TBS,SBUS,IBUS,DSM2,DSMX
Support programmable LED like WS2812
Buzzer Support
Built-in current and voltage sensor
Weight: 4.4g

ESC Parameters:
Compatible with PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: Lipo 1S-2S
Continuous Current: 12A
Firmware: BLHELI_S Z_H_30_REV16_7.HEX

Package List:
RuiBet F4 AIO*1
18awg wire*2
XT30*1
M2*6.5 Damping Ball*4
470UF/10V capacitor *1
2P plug cable*1

EMAX F4 25A AIO FC for Babyhawk II HD

Price $75

https://www.banggood.com/Emax-Babyhawk-II-HD-Spare-Part-AIO-Main-Board-25_5x25_5mm-F4-Flight-Controller-AIO-25A-…-1832192.html

Whoop/toothpick type AIO board from EMAX. This board is used in the EMAX Babyhawk II HD quadcopter. Pretty standard AIO FC with F411 and 25A 4in1 ESC.

Specifications:

Input Voltage: 2-4S
LipoFirmware: STM32F411
FirmwareGyroscope: MPU6000
Onboard:25A BLheli_S 4in1 ESC
Size: 26.5×26.5mm
Mounting Hole: 25.5×25.5mm

NameLessRC AIO412T 2-4S Flight Controller

Price $51.99 

Banggood: https://www.banggood.com/26_5+26_5mm-NameLessRC-AIO412T-F411-Flight-Controller-MPU6000-2-4S-HV-5V-or-2_5A-BEC-p-1547589.html

One of the first toothpick flight controllers in the market in the year 2019. At the date of the release it had a whooping 12A current output capability and could be powered with 2-4S battery. So the NamelessRC was the first to release so called “Toothpick flight controller”. One of the interesting features of this flight controller – it has all the solder pads doubled on the both sides for your convenience.

A lot of them burned up when flashed with the incorrectly detected BLHeli_S firmware with too little deadtime (should be 120).

Release date: 2019-08

NameLessRC AIO412T connection diagram:

MCU:100MHz STM32F411CEU6
IMU:MPU6000
Baro:NO
OSD:BF OSD
Blackbox:NO
Receiver:PPM/SBUS/IBUS/DSM
UART: 2
3.3V:YES
LED Control:BF LED control
Smartaudio:YES
Buzz:YES
Input:2-4S Lipo(2-4S HV Lipo)
BEC:5V 2.5A
ESC protocol:pwm, oneshot125, multishot, dshot150/300/600
ESC Current: 12A 
ESC Burst Current: 16A (10S)
FC FIRMWARE TARGET:Betaflight / MATEK F411(LEGACY)
ESC FIRMWARE TARGET:BLHeli_S / PH120 48K 16.8
Mounting:25.5×25.5mm, φ2
Dimensions:33x33x5mm
Weight:4.6g

NameLessRC 1S 15A Super DVR Toothpick AIO Flight Controller

Price ~$77.90 

This is the one of a kind toothpick AIO flight controller with DVR. However the board became huge, 38x38mm sized, because it had to accommodate the SD Card slot and the DVR chip. This NamelessRC AIO board is for 1S battery and provides up to 15A of current to motors.

Release date: 2021-09

NamelessRC Super DVR AIO flight controller pinout:

Specifications:
Input Voltage: 1S LiPo
MCU: STM32F405
Gyro: MPU6000
OSD: yes
UARTs:3
ESC Connections: yes
FC Firmware: MATEKF405MINI
BEC: 5V 2A
Current Sensor: yes
Buzzer: yes
Barometer: yes
Max. Continuous Current: 15A
Max Burst Current:  ??A (10sec)
ESC Firmware: BLheli_S
Recording Resolution: 720p 30FPS
Max SD Card Size: 32Gb
Recording Format: AVI
Microphone: No
Stack Size: 25x25mm
Dimensions: 38x38x5.5mm
Weight:6g

NewBeeDrone

NewBeeDrone BeeBrain BLV3 AIO F4 FC+ 12A

Price ~$99.99

NewBeeDronehttps://newbeedrone.com/products/newbeedrone-beebrainbl-brushless-v3-whoop-flight-controller

GetFPVhttps://www.getfpv.com/newbeedrone-beebrain-blv3-aio-f4-fc-12a-blheli-s-1-2s-esc.html

Its NewBeeDrone third generation BeeBrain brushless AIO flight controller. Integrated receiver was upgraded – diversity with removable antennas and improved range. ESC now capable up to 12A wih 1-2S battery input. There is also VTX on board with up to 120mW of transmitting power.

NewBeeDrone BeeBrain BLV3 AIO pinout:

Specifications:
UART2 TX and RX are free for the external receiver (un-inverted SBus signal only)
Weight: 6 grams (including antennas and battery connector)
Size: Outer dimensions 29 x 29 x 7.6 mm
Firmware: 48kHz JESC (unlicensed)
Mounting Pattern: 25.5 x 25.5 mm
MCU: STM32F411 MCU
Battery input: 1–2S
ESC current: 12A
VTX: 5mW – 120mW

[To be continued/updated]

My sins list: Not all Flywoo, iFlight, Diatone and BetaFPV boards listed. Prices going up :(, not going to update them. I will just leave the price of the board at the moment of the adding it to the list.  Year 2022 – gyro changes almost on all boards  MPU6000->BMI270.

Update history:
2019-11-07 Article created
2020-07-04 Article updated: iFlight SucceX-D 20A AIO FC, SPCMaker 25A AIO FC
2020-07-16 Article updated: BetaFPV F4 35A, HAKRC F4126 20A/35A
2020-08-11 Article updated: HIFIONRC AIO F7
2020-09-02 Article updated: SPCMaker F411 30A
2020-09-08 Article updated: JHEMCU GHF411 25A/35A
2020-09-14 Article updated: BetaFPV F4 1S AIO VTX
2020-09-14 Article updated: JHEMCU AIO F405 PRO
2021-05-28 Article updated: Emax F4 25A AIO, Happymodel ELRS F4 2G4 FC
2021-06-09 Article updated: Diatone, Flywoo F745 AIO, iFlight 
2021-08-13 Article updated: Holybro FETtec Mini 15A, Flywoo Versatile F4 1S
2021-09-07 Article updated: JHEMCU GH743 AIO
2021-09-14 Article updated: HGLRC boards, NamelessRC AIO412T, Super AIO, NewBeeDrone BLV3
2021-11-01 Article updated: mysterious SPCmaker R66 F4 1S board added
2021-11-14 Article updated: HGLRC Zeus10, Zeus25 V2 boards added.
2022-05-03 Article updated: Aikon F7 AIO, iFlight BLITZ F4411 1S 5A AIO added
022-09-15 Article updated: Neutron F411 5A, 45A, 35A AIO, SpeedyBee F745 AIO added
2022-10-25 Article updated: Neutron F722, F7, H743 AIO added

Comments
  1. Martin Flite
  2. Alec Dvornik
    • montis
  3. Martin
    • montis
  4. Marc Frank
    • montis
      • Marc Frank
  5. Tim
    • montis
  6. Benjamin
    • montis
  7. el pinguino
    • montis
  8. Adeyinka
    • montis
  9. Aria
    • montis
  10. retro_FPV
    • montis

Leave a Reply to el pinguino Cancel reply

Your email address will not be published.

*