Eachine MiniCube – small all-in-one FC

by montis  26/01/2017 | 8:03 2 Posted in New products 

New mini flight controller with ESC and receiver was listed – Eachine Minicube Flight controller. It consists of three 27x27mm sized (mounting holes 20x20mm) boards, stacked one on another. Total tower height is 20mm. Weight is only 9.4 grams.

This all in one solution features F3 flight controller with integrated Betaflight OSD in the middle deck. It has MPU6000 sensor chip working in SPI mode.

On the lower board you’ll have all-in-one ESC  with 4x10A BLHeli ESC. DShot600 ready out of the box.

You can choose between 3 receiver types – DSMX, Flysky and Frsky

EDIT(2017-2-17): Spare parts were listed on Banggood.

Flysky receiver module:

Frsky receiver module:

DSM2/DSMX receiver:

F3 Flight controller with integrated OSD:

4 in 1 ESC 10A BLHeli_S 1-2S BB2 Support Oneshot42 Oneshot125 Multishot Dshot:

 

Eachine Minicube Parts
Frequency range: 2.403-2.479Ghz
Input power: 5V
Response time: 22ms / 11MS
Resolution: 2048
Display method: LED
Operating voltage: 3.3V
Working current: 60MA
Size: 27mm*27mm*7mm
Mount hole:20mm*20mm
Weight: 3.1 g
Antenna length: 100mm
Data format: Serial port
Protoco: DSM2/DSMX
Distance: no ground interference (1 m from the ground ) > 300m
Uses: indoor small aircraft.

Compatible Transmitters: DSM2 / DSMX series of remote control

Channels: PPM 8CH
Model type: Multi-rotor
Frequency range: 2.408-2.475GHz
2.4GHz system: AFHDS 2A
Work Mode: PPM
Transfer method: FHSS
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator
Antenna length: 100mm
No ground interference ( Transmitting and receiving 1 m from the ground): >300m
Working current: 40mA
Size: 27*27*7mm
Mount hole:20mm*20mm
Weight: 3.1g

Compatible Transmitter: Compatible with FS-i4, FS-i6, FS-i6S, FS-i6X, FS-i10, FS-GT2E, FS-GT2G, FS-GT2F

Frequency range: 2.403-2.479Ghz
Channels: 8CH
Work mode :D8 Mode
Output: SBUS
Antenna length: 100mm
No ground interference ( Transmitting and receiving 1 m from the ground): >500m
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator
Working current: 80mA
Dimensions: 27*27*7mm
Weight: 3.5g
Compatible with FRSKY ACCST
Compatible with X9D(Plus)DJT/DFT/DHT
Telemetry: RSSI, 1S-3S voltage (A1), 1S-3S voltage (A2)
Size: 27mm*27mm*5mm
Mount hole: 20mm*20mm
Processor: STM32 F303 MCU
Sensor: SPI Sensor MPU6000
Built-in Betaflight OSD ( Batt voltage, RSSI , Artificial Horizon , Fly mode , -Flytime, Craft name etz.)
Firmware version: Betaflight 3.1 Dshot ready
Target: OmnibusF3
Size: 27mm*27mm*5mm
Mount hole: 20mm*20mm
Firmware version: BLHELI_S 16.5
BB2, 48MHZ Chip
Lipo Battery: 1-2S
Con. Current: 10A
Peak Current: 15A (10S)
BEC: 5V @0.1A
Programming: YES
Betaflight passtrough ready
Dshot600 ready(Default)
Support oneshot42 oneshot125 Multishot Dshot
Damped light on

Related Posts

About Author

montis

Comments
  1. herve

    Hello. i need to make an update but the link betaflight_2.6.1_SPRACINGF3.hex is dead …
    another? I can not find one …
    thank you

    Reply

Leave a Reply

Your email address will not be published.

*